Solid State Integrated Circuits

Click photos to enlarge.

Switch to desktop version

 


Texas Instruments SN514
 
Texas Instruments SN514 Integrated Circuit Texas Instruments SN514 Integrated Circuit

TI's SN51x series of RCTL logic chips, released in 1961, is widely recognized to be the world's first commercially available line of integrated circuits. 'SN' stands for 'Semiconductor Network', TI's nod towards the then-radical idea of combining multiple solid state devices into a single package. The SN51x series chips were manufactured from multiple transistor and diode dies, which were hand-wired together with thread-like interconnect leads inside the package. Constructing chips in this manner was both labor-intensive and expensive: early SN51x series chips sold for over $400 when first released.

These early ICs were primarily targeted towards the military and aerospace industry, and the SN514 (along with the SN510) were the first integrated circuits to orbit the earth. The earliest SN51x series chips were packaged in gold plated flat-packs. This example, a SN514 NOR/NAND gate made in November 1962, abandons the military gold package in favor of a more primitive looking 'block of carbon'-style enclosure. The black package SN51x ICs appear to have been used in both military and civilian applications; at least one surviving photo shows a Litton aerospace guidance system using 'block of carbon'-style SN514 chips.

More...

Fairchild uL914
 
Fairchild uL914 Integrated Circuit Fairchild uL914 Integrated Circuit

In 1959 when Texas Instruments was working towards the creation of the world's first integrated circuit, others were racing towards the finish line from a different direction. A team at Fairchild Semiconductor, headed by an influential group of semiconductor engineers known as the "Tratorous Eight", produced their own integrated circuit technology and announced it to the world mere months after Texas Instruments revealed their device. Fairchild's integrated circuit was manufactured using a radically different technology than the Texas Instruments devices; instead of being built from single transistor dies wired by hand with bond wires, the Fairchild device was built using a complex system of chemical treatments and photographic masks to etch wires directly into a single silicon die. Fairchild's first commercially produced integrated circuit, the uL914, was released in 1961. The uL914 is a RTL duel input NOR gate, and was the first device in Fairchild's 'Micrologic' series of parts. The uL914 is unusual in the realm of collectible electronic 'firsts' in that it is common enough that modern-day collectors can easily obtain one. Unlike most other historic parts which were only produced in small quantities, the uL914 was in production for many years and examples are still readily available on the used market. The device shown here was manufactured in 1970.

The subject of the first integrated circuit is a thorny situation for historians and collectors; Texas Instruments beat Fairchild's announcement of the integrated circuit by four months, but it is the Fairchild 'monolithic' integrated circuit from which all modern devices are descended. Collectors routinely get into furious debate over which device should be considered 'first'. The situation is made worse by the uL914 being common and available while first generation Texas Instruments devices like the SN514 are impossibly rare. Collectors who have been unable to find a part from the SN514 family are uncomfortable giving a crown to a device they will never own, while the few who have Texas Instruments devices through luck or fabulous expense are unwilling to see their possessions devalued by a 'second place' winner.

More...

OKI Intel M85C154
 
OKI Intel M85C154 Piggyback Microcontroller

The Intel M85C154 is a special class of microprocessor known as a 'piggyback' CPU. Piggyback microprocessors are designed to act as a programming development tool and can be easily recognized by the presence of a top mounted socket. In use, the engineer would program a blank EPROM on a desktop computer with their test code, then insert the EPROM into the socket on the microprocessor so the code loaded inside could be tested. Once the code was tested and finalized, a cheaper one-time-programmable microprocessor with built in EPROM would be used in the final product.

The M85C154, an 8 bit CPU based on the Intel 8051, is fairly representative of a typical piggyback microcontroller. This device has a maximum clock speed of 22MHz and 16k of onboard ROM space. Additionally, the M85C154 can address up to 64K of program ROM through it's piggyback socket.

OKI Intel M85C154 Datasheet (PDF)

More...

Cypress CYM1620
 
Cypress CYM1620 Static Ram

The CYM620 is a 1 megabit static ram module built around several leadless ICs mounted to a ceramic carrier. Four of these chips are 256k static RAMs, with the fifth being a decoder IC. The RAM units are grouped into a high and low pair, with the decoder reading the highest position address bit to determine which pair should be active. The TTL level inputs and outputs as well as the substantial hermetic packaging and wide temperature ratings make this a fairly robust memory IC.

The example shown here is the -55C variant, which is rated for commercial use and has an access time of 55 nanoseconds.

Cypress Semiconductor CYM1620 Datasheet (PDF)

More...

Amdahl 470A
 
Amdahl 470A LSI IC

The Amdahl 470A is an unusual LSI CPU component chip that was used in Amdahl's 5860 "supercomputer" mainframe. Amdahl was known for making air-cooled computers in a market dominated by water cooling, which resulted in their chips having a very unique construction. This chip is no exception, the top is dominated by a tall heatsink that would have poked into a forced air cooling channel when installed in a computer. During use, many such chips would be bonded into large arrays to construct a complete CPU. Note that this chip has a Fujitsu makers mark... Fujitsu was Amdahl's largest shareholder and eventually grew to own the company outright.

Amdahl's CPUs were so unique in appearance that many factory defects found their way into Lucite promotional paperweights that were produced by the company as sales samples and awards. This is the predominant form in which they are seen nowadays, as Amdahal's various air cooled chips never saw wide use outside the company.

More...

Amdahl 209
 
Amdahl 209 LSI RAM (76800 209) Amdahl 209 LSI RAM (76800 209)

Even in a world filled with bizzare Amdahal integrated circuits, the Amdahl 209 stands apart. The 209 is an LSI RAM IC in a complicated multi-chip package that was used in the Amdahl 5860 mainframe. This strange looking device is equipped with four distinctive aluminum cooling towers that are bonded to the chip with black epoxy. Each cooling tower is attached to a small square leadless IC, which is in turn bonded to a ceramic carrier. The leadless ICs are actually mounted to the carrier upside down... each has a gold cavity lid pressed tightly against the ceramic of the attached carrier. The four gold pads on the top of the 209 are actually heat spreaders, which connect directly to the underside of the four dies in each package.

Sadly the 209, like most Amdahl chips, has completely undocumented specifications. It is unlikely that these chips will ever see significant use in home-brew electronics projects, due to a lack of reliable connection data.

More...

AMI C1761
 
AMI C1761 Integrated Circuit AMI C1761 Integrated Circuit

Not much is known about this mysterious MOS integrated circuit, other than that it was made by American Micro Systems and has a rather unique package style. The C1761 is packaged is a highly unusual 40 pin white ceramic leadless carrier with a round cavity lid. Earlier versions of this chip make use of a single layer gray trace leadless wafer, though sometime around 1973 AMI switched to a two-piece package which covered the traces in a second layer of ceramic. On the revised package the start and end pin numbers are conveniently printed on the side of the ceramic, and the base is keyed in such a way that prevents the chip from being inserted into it's socket backwards, a feature well ahead of it's time in 1973. We don't currently know the function of this IC, but it is likely a calculator chip or part of a calculator chipset given the manufacturer and package style. Strangely, the device has no insertion marks on the pins and was found in its original packaging, suggesting it was sold in the retail market.

More...

Intel 1301
 
Intel 1301 Integrated Circuit (Mask ROM)

The 1301, first released in 1969, is Intel's first mask rom, and is a compatible replacement for the groundbreaking 1701 UV erasable PROM. The 1301 is programmed at the factory with a metal mask, and was marketed as a low cost alternative to the 1701 for mass-produced items where it was not necessary for the chip to be erasable. The 1301 has a storage capacity of 256 bytes, or 2048 bits, and is also equipped with TTL compatible outputs. The example shown here is an earlier gray trace version, and has a date code from 1972.

More...

Intel 1601
 
Intel 1601 Integrated Circuit (PROM)

The Intel 1601 is a 256 byte PROM that was designed to be drop-in compatible with Intel's 1301 metal mask ROM. A 1601 PROM has a significant advantage over the 1301; in that it can be programmed electronically by the end user without the need for factory-applied masks. Released in 1970, the earliest versions of this chip have opaque gold lids and gray trace ceramic packages. Later versions were simply 1701 UV erasable EPROMS with black vinyl covering up the UV erase window. Unfortunately the black vinyl cover, which has the part number printed on it, has long since fallen away on this example. With the cover removed late model 1601's are basically indistinguishable from an Intel 1701; it is likely that at least a few unidentified 1601s are sitting in chip collections around the world.

More...

IDT 7M912
 
IDT 7M912 9 Bit Static Ram IC IDT 7M912 9 Bit Static Ram IC

The 7M912, manufactured by Integrated Device Technology, is a 64k 9 bit CMOS static ram module constructed out of leadless SRAM chips bonded to a multi-layer ceramic substrate. THe 7M912 is built from nine separate IDT7197 SRAM integrated circuits, five of which are attached to the top surface of a ceramic carrier with the remainder being mounted to the underside. This integrated circuit is military rated, and is designed for use in harsh environments and high demand applications. The 40 pin package has been manufactured with extra-long leads, to prevent socket insertion from fouling the chips on the underside of the package.

IDT also made an 8 bit version of this chip, the 7M812. The 7M812 is identical in function to the 7M912, but only utilizes 8 IDT7197 SRAM ICs.

More...

Toshiba TMM121
 
Toshiba TMM121 EPROM Integrated Circuit Chip Toshiba TMM121 EPROM Integrated Circuit Chip

This strange looking chip is Toshiba's first EPROM device, the TMM121 UV-erase EPROM. Intended to be a competitor to Intel's 1701 UV EPROM, the TMM121 can store 256 bytes in stable UV-erase memory. The chip has an extremely unusual flanged round lid with a central window, which allows the die inside to be exposed to UV light when erasing is desired. The die is housed in a white ceramic carrier with bottom-brazed pins and a large locating notch. The TMM121 was used in Toshiba's first microcomputer, the TLCS-12A, which is an unusual 12 bit system originally designed for use in automotive applications. We do not know the date of manufacture for this device, but it was likely released sometime around 1973.

More...

National Semiconductor MM5203
 
National Semiconductor MM5203 EPROM Integrated Circuit

The National Semiconductor MM5203 is a 2048 bit UV erase PROM that was in production for a number of years. The earliest versions of this chip are mounted in a white ceramic carrier with gold leads and a square cavity window. Later versions switched to a gray ceramic package, but retained the square cavity window and gold leads. The most modern and boring versions of this chip are mounted in a standard ceramic package with a round erase window and tinned leads. In normal operation the window is covered with a label or sticker, to prevent ambient UV light from slowly destroying the data stored on the PROM.

More...

Ferranti ULA 9RK020
 
Ferranti ULA 9RK020 Uncommitted Logic Array IC Ferranti ULA 9RK020 Uncommitted Logic Array IC

The Ferranti 9RK020-3F programmable gate array is a poorly documented device. Not much is known about this chip, other than it is part of Ferranti's line of ULA 'Uncommitted Logic Array' integrated circuits. Ferranti ULA chips saw use in a number of noteworthy computer products from the 1980s, including the Timex Sinclair ZX81 and ZX Spectrum. The 9RK020 is probably most closely related to the 12C021M, a 12 tile programmable array used in the Acorn Electron home computer. The manufacturers of the Acorn Electron relocated nearly all of the computer's support logic into a 12C021M array, resulting in a 90 percent reduction of the Electron's total chip count. The complexity of this ULA caused significant disruption to the Electron's 1983 launch however, resulting in delays and manufacturing shortages as Ferranti struggled to ramp up production of the complicated device.

The Ferranti 9RK020-3F is packaged in a ceramic leadless carrier similar in size and shape to the ULA used in the Acorn Electron. The 9RK020-3F is not leadless however; long gold pins have been brazed to the pads on the carrier, converting it into a surface mount flatpack. We suspect the 9RK020 is a 9 tile device, but it's specifications are otherwise unknown.

More...

Burroughs LSIC B Series Gate Array
 
Burroughs LSIC B Series Gate Array (AMI 1845 9909) Burroughs LSIC B Series Gate Array (AMI 1845 9909)

These largely undocumented parts, produced by AMI, Fairchild, and Burroughs, are LSIC gate arrays used almost exclusively in Burroughs B series minicomputer systems. Burroughs B series computers were bulky console-style machines which were typically built into a desk or table with a large line printer as the only form of display. The AMI 1845-9909, shown in the thumbnail, is believed to be a 150 element gate array originally manufactured for use in a Burroughs B80. Nine of these gate arrays would be combined to form the complete 8 bit central processing unit of the B80. Unfortunately the exact specifications of these chips is unknown; no datasheets or part lists appear to have been released by Burroughs, and the homebrew electronics community has made little progress in unlocking their secrets. Despite this, Burroughs processor chips see a decent amount of turnover amongst chip collectors, due almost entirely to their strange form factor. Burroughs gate arrays are packaged in large white ceramic pin grid carriers with gold traces and a central round cavity lid, and have a distinct appearance unlike any other integrated circuit. Electronics lore has that the original Burroughs service technicians referred to these devices as 'fried egg chips' due to their unusual packaging. The example shown in the thumbnail was manufactured in 1976.

More...

CDC Cyber 205 A68 Gate Array
 
CDC Cyber 205 A68 Gate Array  CDC Cyber 205 A68 Gate Array

This very unusual device is an ECL gate array prototype intended for use in a Control Data Corporation CDC Cyber 205 supercomputer. Each ECL gate array contains 168 logic gates; thousands were required in the construction of a complete Cyber 205. The gate arrays are designed to be actively cooled with a Freon refrigeration system, which required the use of a specialized leadless ceramic carrier with a heat spreader that extends beyond the bottom of the chip package. When installed inside a Cyber 205, the heat spreaders on each gate array would directly contact copper pipes filled with Freon, which would cool the chips down to operating temperature. The examples shown here are pre-production engineering samples, which have an open cavity that allows the die inside to be clearly seen. Production gate arrays would have a metal lid covering the chip die. This gate array is believed to have been made sometime between 1982 and 1983.

An interesting side story is that a larger version of this chip was produced by Motorola for use by the Control Data Corporation spinoff ETA in a new type of cryogenically cooled supercomputer; the ETA-10. This larger gate array, which was packaged in a flat ceramic carrier with contact pads along all four edges, would have contained approximately 8000 gates. The ETA-10, which was designed to operated while immersed in a bath of liquid nitrogen, had only limited commercial production.

More...

Intersil 6100
 
Intersil 6100 Microprocessor

The Intersil 6100 is a 12 bit CMOS microprocessor first produced by Intersil in 1975. This relatively popular microprocessor family was manufactured in white, purple and plastic versions by both Intersil and Harris Semiconductor. The 6100 used the same instruction set as the popular PDP-8 series of minicomputers, and as a result was used in a number of late-1970s computer systems and logic controllers. One of the most iconic uses of the 6100 was as the CPU in Digital Equipment Corporation's line of DECmate personal computers. These machines took advantage of the 6100s instruction set to run reduced versions of the operating system used on some PDP-8 machines, although later DECmate computers included a Zilog Z80 for CP/M compatibility.

More...

ITT AN/ALQ-136 Countermeasures Processor
 
ITT AN/ALQ-136 Countermeasures Processor (ITT 80063SM-A-919797) ITT AN/ALQ-136 Countermeasures Processor (ITT 80063SM-A-919797)

This enormous hybrid integrated circuit, originally manufactured by ITT, was built to be the 'brain' of the AN/ALQ-136 countermeasures system on a US Army Cobra attack helicopter. This is one of the largest and most complicated hybrid integrated circuits we have ever seen; the processor contains almost 100 dies, which are sealed in a huge 116 pin quad inline metal package. The core of this processor is built around four AMD AM2901B bit slice processors. Each AM2901 can handle 4 bit processing; by linking four dies together, a 16 bit 16MHz processor is created. The processor also contains ROMs which store the radar definitions of enemy aircraft, a questionable design choice since it requires the entire processor to be replaced to update the system with definitions for new aircraft. The ITT AN/ALQ-136 Countermeasures System was first released in 1982, and the example processor shown here was manufactured in 1986.

More...

Crossfiber Optical Switching IC
 
Crossfiber Optical Switching IC  Crossfiber Optical Switching IC

Here is a device that, while not particularly vintage, is rather unusual; a Crossfiber optical switching chip. A crossfiber chip is a relatively new invention that is used for optical computing and routing. The IC has an array of pinhead mirrors mounted on 2 axis pivots, which can be moved electrically to bounce optical beams in different directions. In normal use, the IC would be mounted in a frame facing a fiber optic array; the mirrors could then be used to direct signals between adjacent fibers. This example contains a 16x16 array composed of 256 mirrors each about a millimeter in diameter; in effect forming a flip dot display intended to be gazed upon by a fiber optic bundle instead of human eyes. The unit shown here is a used laboratory sample and has no manufacturer markings, but we believe it was produced sometime around 2009.

Unfortunately, crossfiber IC's have yet to see widespread availability in the homebrew electronics community. Datasheets and example circuits are not readily available, and the home electronics experimenter is likely to find building a project around one of the these chips a challenging experience.

More...

Atmel AT27C256R
 
Atmel AT27C256R EPROM IC

Devices included in this entry:

Atmel AT27C256R (256K leadless carrier; pictured in thumbnail)
Microchip 27C512 (512K leadless carrier)


Atmel's AT27C256R is a 256K EPROM in a tiny surface mount leadless package. Though the majority of modern 27C256 devices are one time programmable IC's in anonymous plastic enclosures, this earlier gold and ceramic example includes a glass window for UV erasure. Later UV erasure versions of this part use an all-ceramic package, but retain the circular UV window.

More...

Raytheon HE0909
 
Raytheon HE0909 Integrated Circuit (HE0909-0-F-002) Raytheon HE0909 Integrated Circuit (HE0909-0-F-002)

The HE0909-0-F-002 is a completely undocumented part in an uncommon package. Even the manufacturer of this device is in question, the ceramic package has markings indicating this chip was produced by Teledyne, but electronics lore suggests this device was manufactured by Raytheon. What can be said is that this chip was likely intended for aerospace applications, based on it's unusual construction style. The HE0909 is encased in a flat ceramic carrier with top-mounted leads and a diamond shaped cavity lid. Typically a chip with this type would be installed in a square cutout in the target PCB, allowing the top-mounted leads to lay flat on the pads of the PCB. The black plastic frame is not part of the device; it is a protective carrier designed to support the fragile pins during transport, and would have been discarded when the chip was installed in its final destination.

More...

Cypress 22V10
 
Cypress 22V10 PAL Logic Array IC (22V10B)

The 22V10B is a tiny programmable logic array (PAL), which contains a number of logic gates whose connections can be selected electronically. This chip was manufactured in a number of different package types, the example shown here contains a prominent glass window, which allows the chip to be erased with UV light and re-used. The window covers nearly the entire top surface of the chip, forcing the part number to be printed directly on the window's surface. ICs deployed into commercially manufactured devices typically omit the window to save costs, since the chip would never need to be reprogrammed outside of the factory. The gate array inside the 22V10 is wired in a cross connected matrix and can be programmed to emulate logic systems in the range of 500 to 800 separate gates. The 22V10 also makes use of "Macro Cells" across each of it's 10 outputs, which can be switched to become additional inputs on the fly. The 22V10B shown in the photo was likely manufactured exclusively by Cypress Semiconductor.

Cypress Semiconductor 22V10B Datasheet (PDF)

More...

Tektronix TK2048M M424A
 
Tektronix TK2048M M424A CCD Image Sensor Tektronix TK2048M M424A CCD Image Sensor

This extremely large CCD, originally manufactured by Tektronix, has an unusual pedigree; it is a prototype of one of the image sensors that would eventually fly into space aboard the Hubble Space Telescope. This device has a complicated and confusing history. In 1985 Textronix released a press statement announcing the creation of what was believed to be the largest CCD imager in the world, the TK2048M, featuring a picture of this device as the prototype. Textronix anticipated the 4-megapixel TK2048M would be available for sale in 1985 for the price of $40,000 per unit. The device that was actually released in 1986 under the TK2048M part number had a significant difference from the prototype shown here however; instead of being packaged in a ceramic sandwich carrier, production units are installed in an 80 pin Kovar bathtub package. In 1989 Textronix announced that a pair of modified TK2048M CCDs would be the 'eyes' of the Hubble Space Telescope's imaging spectrograph. However, the imaging spectrograph was not ready in time for Hubble's 1990 launch date, and in 1993 Tektronix spun their CCD division off into a new company, Scientific Imaging Technologies, which continued to make the TK2048M as a new part number, the SI-424. A pair of SI-424's did eventually fly to Hubble when the imaging spectrograph was completed and installed in 1997. SI-424's have also been installed in a number of other historic devices, including the Keck telescope and the Sloan Digital Sky Survey telescope, which contains 30 SI-424 CCDs arranged in a grid and graded for different spectral responses.

More...

General Instrument P6828
 
General Instrument P6828 Integrated Circuit (P6828B)

The General Instrument P6828B is an entirely undocumented integrated circuit. No descriptions or information appear to exist on datasheet or partminer sites, and the examples we found did not include any supporting documentation. The device itself is encased in a rectangular gold bathtub package with a white glass base and gold leads. The underside gold leads are arranged in a pin grid pattern and have a square cross-section, most likely to facilitate wire wrap installation. Unfortunately, not much else can be determined from an external examination, and this device is uncommon enough that cutting the lid off of one for a look at the internals seems like borderline heresy.

If you can identify this device, please contact us.

More...

Philips NXA1010
 
Philips NXA1010 CCD Image Sensor Philips NXA1010 CCD Image Sensor

The Philips NXA1010 is a 604 x 575 line CCD image sensor designed for use in monochrome PAL video cameras. The NXA1010 is a frame transfer CCD; only half of its light-sensing surface is used for generating images, the second half of the CCD area is set aside as a frame buffer storage area. On the CCD die this storage area is easily visible, as the half of the CCD set aside for frame transfer has been covered with an opaque barrier material. The pixel rows in the CCD sensor area are organized into parallel shift registers, which allows a captured image to be quickly 'slid' under the barrier material for safekeeping until it can be transferred off of the CCD die. The additional length added to the die for the frame transfer area makes it too large to fit in a normal DIP package; the NXA1010 makes use of a modified 24 pin ceramic carrier with an elongated cavity to provide the extra room needed. The NXA1010 is believed to have been released in 1984.

Philips also produced the NXA1020, a same-resolution device that was capable of producing color output. The NXA1020 uses an identical CCD, but includes a color bar filter which has been bonded to the CCD's surface.

More...

XGA2 Leadless CCD (Unknown P/N)
 
XGA2 Leadless CCD (Unknown P/N)  XGA2 Leadless CCD (Unknown P/N)

We do not know much about this part. This device appears to be a CCD image sensor from the late 1980s, but the device has no part number or manufacturer's logo. The only writing anywhere on this CCD is the word 'XGA2' printed in block letters on the die, which suggests this device produces images at the XGA resolution; 1024 x768 pixels.This would place the manufacture date of this CCD no earlier than 1990, the release date for XGA, but the copious amounts of gold used in the construction of the device's ceramic package would be rather high for an item made in the 1990s. The 68 pin package for this CCD includes a glass window over the die itself, to protect the CCD surface from dust and the fingers of clumsy electronics engineers.

More...

Fairchild FCCD 143D
 
Fairchild FCCD 143D Linear CCD

the FCCD 143D is a linear CCD, which is a light sensor that contains an array of photosensitive elements fixed end to end in a single line. Images are drawn by scanning a beam of light across the length of the CCD, capturing one line at a time. In this device, the light sensitive die has been packaged in a large 28 pin ceramic DIP with a glass cavity lid. The die for this device is much larger than what would be used in a conventional integrated circuit, and spans nearly the entire length of the device.

Analog Devices ADC80
 
Analog Devices ADC80 Analog to Digital Converter IC Analog Devices ADC80 Analog to Digital Converter IC

The ADC80, made by Analog Devices as well as other manufacturers, is a 12 bit successive approximation analog to digital converter. Analog Devices touts the ADC80's lack of reliance on external components; it's clear this was accomplished by physically relocating components to the interior of the IC package. The ADC80 makes use of a large specialized carrier, which contains six integrated circuit dies as well as a number of lesser components. The carrier also contains a laser trimmed 6.3 volt zener diode reference source, which is accessible through an external pin on the package. The ADC80 seems to have gone through significant package variation over the years, with early examples being packaged in a purple ceramic bathtub carrier with bottom brazed pins. Later versions are packaged in more traditional flat ceramic carriers with a hollow ceramic lid covering the cavity. The example shown here a metal cavity variation, which replaces the ceramic cavity lid with a metal lid and gold-lined cavity.

More...

Lucent T 7102A
 
Lucent T 7102A Protocol Controller

Little is known about the Lucent 7102A, other than that it is an X.25/X.75 protocol controller that was in use in telephone switching equipment in the early 1990s. The most distinctive feature of this IC is it's unusual pin configuration; the underside of the chip contains four rows of pins arranged into four 18 pin DIP arrays, eliminating the need for a custom socket.

More...

Western Electric Integrated Circuits
 
Western Electric Integrated Circuits

Devices included in this entry:

Western Electric 1C parallel to serial interface (16-pin ceramic flat pack; pictured in thumbnail)
Western Electric 618 APB (16-pin ceramic DIP)


Western Electric manufactured a wide range of obscure and undocumented integrated circuits, many of which featured nondescript packages and a total lack of package-marked part numbers. Like HP, Western Electric IC packages give you nothing, except the vague statement that the device was made by Western Electric. The packages of many Western Electric integrated circuits are so anonymous in appearance that they are frequently misidentified as resistor networks by electronics resellers.

More...

Westren Electric Trimline Controller IC
 
Westren Electric Trimline Controller IC

This bizarre looking hybrid integrated circuit is the controller used in many Western Electric Trimline phone handsets. The device makes use of a rather unusual construction technique in which multiple layers of glass with attached semiconductors and passives are bonded together and coated in resin. Numerous ball bond wires connect the different layers of the integrated circuit electrically. The passive resistors can be clearly seen through the top of the device as tracks of resistive material painted or etched onto the surface of the glass substrate.

©2000-2026 Industrial Alchemy. All rights reserved. | Switch to desktop version | Contact |